Try these Luxury Watch Faces for your Smart Watch!

Our smartwatch already comes with a bunch of preinstalled watch faces. On top of that, you can also get a plethora of them from numerous third-party sites. But the one that we are about to share here, it’s safe to say you wouldn’t have come across any of them, ever. So let’s jump off the hype mill and make you aware of some of the most luxurious watch faces for your smart watch. Follow along.

  • List of Luxury Watch Faces
  • Download Luxury Watch Faces
  • How to Install Luxury Watch Faces on any SmartWatch METHOD 1: Via Bugjaeger App METHOD 2: Via Wear Installer 2

List of Luxury Watch Faces

download install Luxury Watch Faces for Smart Watch - 1

You can try out the following ultra luxury watch faces on your smart watches right away!

  • Omega
  • Jaeger-Le Coultre
  • Longines
  • Piaget
  • Vacheron Constantin
  • Tag Heuer
  • Doxa
  • Carl F Bucherer
  • Breitling
  • Audemars Piguet
  • Rolex
  • BlancPain

Download Luxury Watch Faces

You may now get hold of the desired luxury watch face/faces for your smartwatch from below:

DOWNLOAD LINK 

[Credits: XDA Member Delany237]

How to Install Luxury Watch Faces on any SmartWatch

We are listing two different methods through which you can get this job done. Go through both of them and then try out the one that is in sync with your requirement.

METHOD 1: Via Bugjaeger App

  1. To begin with, download the desired WatchFace APK from above onto your device.
  2. Now, download and install the Bugjaeger app on your device.
  3. Then launch it and tap on the New Connection icon at the top right. Keep this window open.
  4. After that, head over to Settings > About Watch > Software and tap Software Version 7 times.
  5. Then go to Developer Options and enable the toggle next to ADB Debugging.
  6. Next, go to Wireless Debugging and enable it. Then scroll down and tap on ‘Pair New Device’.
  7. You’ll get the pairing code, IP Address, and Port. So type in the IP Address and Port in the Bugjaeger app and hit Pair.
  8. Then type in the IP Address, Port, and WiFi Pairing Code in the app and hit Pair.
  9. Finally, type in the IP Address and Port number and hit Connect. NOTE: The Port number should be from the ‘IP Address and Port’ section of the watch [not from the Pair with Device section]. Your watch should now be connected to your device via Bugjaeger.
  10. Now, go to the third tab of Bugjaeger and hit the Plus icon at the bottom right.
  11. Now choose Select APK file, select the desired APK, and it will be installed.
  12. Now launch the Galaxy Wearable app on your device, go to Faces, and scroll down to the Downloads section.
  13. Then just tap on the desired watch face. It will be installed on your watch right away.

METHOD 2: Via Wear Installer 2

  1. To begin with, download the desired WatchFace APK from above onto your device.
  2. Next up, download and install the Wear Installer 2 app from the Play Store. Then launch it and keep it open.
  3. After that, head over to Settings > About Watch > Software and tap Software Version 7 times.
  4. Then go to Developer Options and enable the toggle next to ADB Debugging.
  5. Next, go to Wireless Debugging and enable it. Then scroll down and tap on ‘Pair New Device’.
  6. Then launch it, note down the IP Address, and type it in the Wear Installer 2 app.
  7. Now, tap on the overflow icon and select Pair with Watch.
  8. Then tap Enable. Now type in the pairing code and pairing port in the app, which is shown on the watch.
  9. You’ll now be taken to the app’s main page. Over there, type in the pairing code which is shown in the watch’s IP Address and Port section [and not the one which was shown in the Pair New Device section].
  10. Finally, hit Install. The app will now be installed on your watch [this might take some time, depending on the file’s size]. Once done, hit Finish.
  11. That’s it. You may now launch the app from your watch and close ADB Debugging as well [optional, but recommended as it will save your watch’s battery].
  12. Now that the pairing is done, from the next time onwards, whenever you want to install any APK on your watch, then just enter the port number from the IP Address and Port section of the watch, see below, [and not the Pair New Device section of the watch] in the app and hit Done.
  • How to Install Gemini on Samsung Galaxy Watch
  • GBoard not working on Galaxy Watch 6/5/4: Is there a Fix?
  • How to Backup Samsung Galaxy Watch via Pixel Device
  • Cannot Pair Galaxy Watch with Rooted Device: How to Fix
Google preferred - 2 Google preferred - 3

(Cancel Reply)

Δ